Home > Cap Designs


Cap designs vary and should be selected according to individual needs. The descriptions and information given for each of the cap designs below is for informational purposes only. Long-time wearers should make selections according to their history and experience.

Image Hosting by PictureTrail.com

Full Lace:
This cap design offers complete transparency, but does not offer extra stretch. It is ideal for those with partial to complete hair loss. A totally natural scalp appearance is possible when parted anywhere throughout the cap. A full perimeter bond is required for this cap design. Wig can be worn in a high ponytail. For those with growing hair underneath, we suggest that you add 1/4 to 1/2 inch to measurements #1, #2 and #5.

Lace with Stretch/Ear Tabs:
This cap design has a stretch panel that stretches from ear to ear across the crown, which will extend one or more of the 6 head measurements when needed. Recommended for those who will continue to grow hair underneath. Bonding behind the ear is not necessary. Wig can be worn in a high ponytail.

Lace with Crown Stretch:
This cap design has a crown panel that stretches from ear to ear across the crown, which will extend one or more of the 6 head measurements when needed. Recommended for those who will continue to grow hair underneath the wig. Full bonding is necessary. Wig can be worn in a high ponytail.

Lace with Crown Stretch/Clips:
This cap has a stretch panel in the crown that will stretch to accommodate hair growing underneath. Recommended for those who do not want to bond their nape area. Bonding is only necessary for the front hairline. Wig can be worn in a high ponytail if ones own back hair is long enough to blend seamlessly with the hair of the wig. Clips are attached on the back lower edge for secure attachment.

Lace with Crown Stretch/Adjustable Strap/Combs:
This cap has a panel in the crown that will stretch to accommodate hair growing underneath. Recommended for those who do not want to bond their nape area. Bonding is only necessary for the front hairline. Wig cannot be worn in a high ponytail but can be adjusted to a snug fit with the back strap, crown and nap combs.

Glueless:
This cap design has special panels at the temple that hug the head and allows it to be worn with little or no adhesive when the back strap is adjusted snuggly. Measurements must be accurate for an optimal fit. Full parting capabilities are possible. Hair can not be worn in a high ponytail, but a low ponytail.

Lace with Crown Stretch/Thin Skin Perimeter:
This cap design has a crown stretch panel, with a wide polyurethane strip around the entire perimeter of the cap. The Polyurethane strip does not offer stretch, however the crown stretch panel will allow for hair growing under the wig, Full perimeter bonding is necessary. Wig can be worn in a high ponytail.

Full Lace With Mono-filament Crown:
This cap design supposedly offers complete transparency with a sheer, light-weight Polypropylene panel on the crown to achieve natural partings for realistic scalp appearance. Measurements must be exact for a proper fit, as cap does not stretch. Hair can be worn in a high ponytail. PLEASE NOTE: This cap design is a personal preference and should only be worn by those who are familiar with any tweaking that may be necessary to simulate a natural scalp appearance, therefore wigs and hair units made with mono-filament crown tops cannot be returned if you are unhappy with the appearance. IMPORTANT: Because of the intricate work involved in making mono wigs, minimum production time is 6 to 7 weeks.

Lace w/Silk Top:
This cap design is available with a 4x4 inch or 5x5 inch silk top panel at the front crown area that simulates a scalp appearance. Because Silk Tops are opaque compared to the sheer lace, they will often times require dyeing to match your skin tone. For this reason, you should not order this cap design unless you are experienced with coloring Silk Tops. Hair can be worn in a high ponytail. Cap does not offer stretch. It is best suited for those with little or no hair. For those with growing hair, we suggest that you add 1/4 to 1/2 inch to measurements #1, #2 and #5 for a better fit. PLEASE NOTE: This cap design is a personal preference and should only be worn by those who are familiar with any tweaking that may be necessary to simulate a natural scalp appearance, therefore wigs and hair units made with mono-filament crown tops cannot be returned if you are unhappy with the appearance. IMPORTANT: Because of the intricate work involved in making silk top wigs, minimum production time is 6 to 7 weeks.

Frontals, 1/2 Wigs, 3/4 Wigs and Closures:
These essential hair units conceal thin or bald hairlines and crowns, and attach to existing back hair with clips or sewn on to a track. The end result is an easily installed unit that looks and feels just like your own hair. Please see product page for unit pictures.